Search
38 articles for “yield strength”
-
Mechanical and Microstructure Properties of Al and SiC Reinforced Aluminum-Based Metal Matrix Composite
Abstract: It is becoming increasingly difficult to design new technical materials that are resistant to wear damage and corrosion degradation in severe service circumstances. Unfortunately, even with crucial passive metals, like Al alloys, there is often a compromise between wear and corrosion resistance. Because of the unfavorable galvanic connection between the precipitates and the matrix, precipitates not only harden the material but also accelerate corrosion. This research established that a supersaturated …
Published in International Journal of Metallurgy and Alloys · Vol. 11, Issue 1, 2025 · pp. 26–43 Read article
-
Correlation between full width at half maximum (FWHM) of XRD peak with mechanical properties
Abstract: Full width at half maximum (FWHM) of XRD profiles characterizes different mechanical properties. However, there is no literature available that discusses about the correlation between the FWHM of XRD peaks with mechanical properties (ultimate tensile strength, yield strength, strain hardening coefficient and micro-hardness) upon plastic deformation. Martensitic stainless steel (type 410) and Ferritic stainless steel (type 430) samples were plastically deformed under different strain rate using tensile testing machine. Variation …
Published in International Journal of Metallurgy and Alloys · Vol. 1, Issue 1, 2015 · pp. 15–23 Read article
-
Tri-Route Orchestration of Sr-Modification, MoldVibration, and T6 Treatment on the Microstructure andPerformance of A356 Alloy
Abstract: This study examines the cascade effects of chemical modification, mechanical mold vibration during solidification, and subsequent T6 heat treatment on the microstructural evolution and multi-property enhancement of A356 Alloy cast via permanent mold casting. Initially Sodium (Na) modifying flux (2– 4 wt%) and Strontium (Sr) elemental modifier (0.01–0.05 wt%) were implemented to refine the morphology of eutectic silicon; Sr addition at an optimal concentration of 0.04 wt.% yielded superior eutectic …
Published in International Journal of Manufacturing and Materials Processing · Vol. 12, Issue 2, 2026 · pp. 13–25 Read article
-
Selection of Gear Materials Using MCDM-TOPSIS Approach
Abstract: Materials selection are a key issue in the optimal design of the industrial product. Material selection is a difficult and subtle task because of an immense number of different available materials. Increasing demand for gears in the different field of applications has forced manufacturers to design and develop gears which compete in the global market and satisfy the user requirements as well as environmental conditions. Various attributes of gear materials …
Published in International Journal of Manufacturing and Materials Processing · Vol. 3, Issue 2, 2017 · pp. 10–15 Read article
-
Influence of Different Quenching Media on the Mechanical Properties of Mild Steel – A Case Study of Coconut Oil, Mineral Oil, Jatropha Oil, and Water
Abstract: This study elucidates how local cooling agents, such as coconut oil and jatropha oil, influence the mechanical characteristics of heat-treated mild steel. Tensile testing, Brinell hardness testing, and microstructural analysis were conducted on both heat-treated and untreated samples. The results show observable differences in the heat-treated materials’ mechanical characteristics. Specifically, the yield strength increased across all quenched media, while the ultimate tensile strength decreased for samples cooled with coconut oil …
Published in International Journal of Metallurgy and Alloys · Vol. 10, Issue 2, 2024 · pp. 1–8 Read article
-
Characterization of AL-2014 TIG Welded Joints
Abstract: Abstract – This experimental study presents a comprehensive investigation into the tensile strength of TIG-welded butt joints made from Al-2014 alloy, a material that find applications in aerospace and structural engineering due to its excellent machinability and high strength to weight ratio. Welding Al-2014 alloy is challenging because it is more prone to hot cracking, oxide layer formation and thermal distortion. Therefore, it is very important to optimize welding parameters …
Published in International Journal of Manufacturing and Materials Processing · Vol. 12, Issue 1, 2026 · pp. 25–31 Read article
-
An Investigation of Properties Nanoparticles Reinforced Thermoplastic Nanocomposites
Abstract: Nanoparticles and nanocomposites find widespread uses in a variety of fields, such as building materials, architecture, optics, food packaging, optoelectronics, semiconductors, medicine, textiles, cosmetics, and catalysis. Compared to their microparticle cousins, polymeric nanocomposites-a unique family of materials-perform better because they blend organic polymers with inorganic nanoparticles. As a result, they ought to improve the domain of engineering applications. Inorganic nanoparticles can significantly alter the properties of a polymer matrix. Flexible …
Published in International Journal of Nanomaterials and Nanostructures · Vol. 10, Issue 2, 2024 · pp. 54–64 Read article
-
Mechanical, Thermal, and Electrical Properties of Poly(ether-ester)-Based Thermoplastic Elastomer Composites Filled with ZnO Nanoparticles
Abstract: A highly helpful technique to create novel polymeric materials with ordered and customized features is blending two or more immiscible polymers. The outstanding balance between processability and physical characteristics of thermoplastic polyester elastomers, particularly when using hydrogenated styrene–butadiene copolymer, makes them appealing materials for a variety of applications, including the automotive industry. New opportunities for tailored flexible composites with improved mechanical and chemical properties are made possible by reinforced polymers …
Published in International Journal of Nanomaterials and Nanostructures · Vol. 10, Issue 2, 2024 · pp. 33–42 Read article
-
Assessment of Depth of Girder of Railway Bridge
Abstract: The depth of a railway bridge girder is primarily determined by the span of the girder. The load exertedon the girder by passing trains induces a bending tendency, which is counteracted by the girder'sthickness or depth. This structural depth is crucial in neutralizing the bending moments and ensuringthe stability and safety of the bridge. Furthermore, the calculated depth or thickness of the girder mustbe validated against permissible deflection limits to …
Published in International Journal of Transportation Engineering and Traffic System · Vol. 10, Issue 1, 2024 · pp. 1–7 Read article
-
Analysis of Box Culvert with Different Aspect Ratio
Abstract: Box culverts are the default buried structure type, where pipe solutions are not suitable. Their larger openings are often required to provide adequate hydraulic capacity. Box culverts are also frequently used for pedestrian or cattle underpasses. The reinforcement used in concrete box culverts can be either conventional bar reinforcement or welded wire fabric. Welded wire fabric has yield strength slightly larger than conventional bar reinforcement. Standard designs for precast concrete …
Published in International Journal of Transportation Engineering and Traffic System · Vol. 3, Issue 1, 2017 · pp. 32–38 Read article
-
Bauschinger Effect on Micro-Lattice of Ti-6al-4v Implants by Using Finite Element Analysis
Abstract: This research's primary objective is to apply the Bauschinger effect to develop a micro-lattice of titanium alloy implants using nonlinear finite element analysis. In orthopedics, micro-lattice cellular Ti-6Al-4V designs with controlled porosity and pore sizes that are good for tissue ingrowth and biological mechanisms are often used. In this investigation, CAD models of various unit lattice structures were generated using Intra-Lattice software, incorporating design parameters such as strut length, strut …
Published in International Journal of Nanomaterials and Nanostructures · Vol. 9, Issue 1, 2023 · pp. 18–24 Read article
-
EFFECT OF HEAT AGEING ON MECHANICAL PROPERTIES OF POLYAMIDE 6(NYLON 6) & POLYAMIDE 12(NYLON 12)
Abstract: Polyamide 6 or Nylon 6(PA 6) and polyamide 12 or Nylon 12 (PA 12) are well known engineering semi-crystalline polar polymers characterized by the presence of amide linkage (-CONH-) in the repeating units of their chains. The glass transition temperature (Tg) of PA 6 and PA 12 is ~50 °C and ~37 °C respectively. PA 6 is widely used for gears and bearings, fittings in automobile industry for under hood …
Published in International Journal of Polymer Science and Engineering · Vol. 2, Issue 2, 2016 · pp. 1–12 Read article
-
Experimental Investigation To Study the Effect of Heat Treatment on Mechanical Properties and Microstructure of Duplex Stainless Steel
Abstract: The broad aim of this paper is to study the enhancement in mechanical properties of duplex steel by thermomechanical processing. Solution annealing followed by water quenching, hot rolling to 10% and 30%, cryo-rolling to 80% and 90% and ageing at 600°C and 1000°C for 5 hrs were the treatments given. The cryo-rolled samples were used for impact testing and rest for tensile testing. Microstructural analysis was done after the various …
Published in International Journal of Mechanics and Design · Vol. 2, Issue 2, 2016 · pp. 32–42 Read article
-
Optimisation of Ratio of Center Distance of Adjacent Hole to Diameter of Pre-stressed Holes by FEA
Abstract: Residual compressive stress zone around a fastener hole is introduced by a process called pre-stressing. This is being done to reduce adverse effect of cyclic tensile stress and to restrict the fatigue crack growth due to material flaws or imperfect surfaces. The objective of this investigation is to optimize the inter-hole distance between adjacent cold expanded holes on a plate restricting the deformation of material between holes to the elastic …
Published in International Journal of Structural Mechanics and Finite Elements · Vol. 6, Issue 2, 2020 · pp. 40–48 Read article
-
An Investigation of Physico-mechanical Characterizations of Recycled Cellulose Fiber and Glass Fiber-polypropylene Hybrid Composite
Abstract: In the field of marine engineering design, polymeric composites reinforced with natural fibers are extensively used. The results of this study demonstrate that these properties can be enhanced by adding glass fiber (GF) to recycled cellulose fiber (rCF) plastic composites. The performance of rCF and rCF/GF hybrid polypropylene (PP) composites is being studied in the current experimental effort. On the tensile behavior and impact strength of composites containing 30 wt% …
Published in International Journal of Nanomaterials and Nanostructures · Vol. 9, Issue 1, 2023 · pp. 1–10 Read article
-
Performance Analysis of High-Volume Fly Ash and Recycled Aggregate in M50 Concrete: Workability and Compressive Strength
Abstract: Abstract This study evaluates the impact of recycled aggregate (RA) and high-volume fly ash (HVFA) on the workability and compressive strength of M50 grade concrete. Slump tests were conducted for various water-cement ratios, using a mix ratio of 1:0.69:2.29 and a high-range water reducer. The compressive strength of concrete mixtures incorporating varying percentages of RA and FA was measured at 7, 28, and 90 days. Results indicate that replacing natural …
Published in International Journal of Concrete Technology · Vol. 10, Issue 2, 2024 · pp. 25–32 Read article
-
Effect of Replacing Rice Husk Ash with Cement and Granulated Blast Furnace Slag with Fine Aggregates on High Performance Concrete
Abstract: Cement and sand are the basic materials for any concrete construction. Now a day’s due to erosion of rivers and considering environmental issues, there is a scarcity of river sand. Many researchers are finding different materials to replace sand and one of the major materials considered in this study is granulated blast furnace slag (GBFS). In recent times, instead of cement many alternative materials are being used as the binding …
Published in International Journal of Concrete Technology · Vol. 2, Issue 2, 2016 · pp. 30–35 Read article
-
Optimizing Characteristics of Ferro-Geopolymer Composites for Structural Applications
Abstract: Abstract This study focuses on developing an optimal mix for geopolymer mortar (GPM) using varying molarities of NaOH solution and different binder-to-aggregate ratios. The primary objective was to determine the mix that yields the highest compressive strength. GPM cubes were prepared and subjected to two curing methods – oven curing and steam curing. Compressive strength tests were conducted at 3, 7, and 28 days. The results show that the compressive …
Published in International Journal of Concrete Technology · Vol. 10, Issue 2, 2024 · pp. 17–22 Read article
-
A REVIEW ON SOUND WAVES AND ITS EFFECTS ON PLANTS
Abstract: The overall performance and development of cell is due to the elongation and proliferation of cell. The interconnection among various phenomena’s and sound waves is a significant topic to study in order to check the various pros and cons of sound waves on different functions of cell. Experiments show that sound waves of various frequencies, SPLS and of different kinds greatly affect the plants. Certain frequency sound waves such as …
Published in International Journal of Environmental Chemistry · Vol. 6, Issue 1, 2020 · pp. 1–14 Read article
-
Process Optimization of Copper Phthalocyanine Pigment PB15:3: A Sustainable Solvent Reduction Strategy for Industrial Applications
Abstract: Copper phthalocyanine pigments, particularly PB15:3 (beta-phase), represent cornerstone materials in the global colorants industry with applications spanning automotive coatings, printing inks, and engineering plastics. Conventional synthesis routes for PB15:3 necessitate copious volumes of high-boiling organic solvents – predominantly dimethylaminoethanol (DMAE) and aromatic hydrocarbons – posing significant environmental burdens and economic constraints. This study presents a systematic investigation of solvent quantity optimization in the pigment finishing process of CI Pigment Blue …
Published in International Journal of Polymer Science and Engineering · Vol. 12, Issue 1, 2026 · pp. 21–40 Read article