Search
141 articles for “Wear”
-
To Enhance Wear Resistance of Cast Iron Using Thermal Spray Coating Techniques
Abstract: In the present research work, an experimental study is being carried out to evaluate and enhance wear resistance of cast iron using thermal spray coating techniques. For this work, coating materials used were WC–Co–Cr and Ni–Cr in powdered form, and the coating was done by D-gun (detonation-gun) method. Wear behavior was investigated using pin-on disc apparatus at 30,40 and 50N on both coated and uncoated samples of cast iron, and …
Published in International Journal of Manufacturing and Materials Processing · Vol. 6, Issue 1, 2020 · pp. 1–5 Read article
-
Enhancement of Wear Resistance of AISI D2 Steel Slitter using Deep Cryogenic Treatment
Abstract: The cooling of material below-150C for sufficient soaking period is termed as deep cryogenic treatment (DCT). There is an improvement in wear resistance and hardness of tool and die steels due to deep cryogenic treatment. The improvement in wear resistance is observed due to precipitation of fine secondary carbides and even distribution of carbides. In present study, the slitters of AISI D2 cold work air hardening type tool steel are …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 2, 2021 · pp. 17–28 Read article
-
Taguchi based validation of wear prediction for Zirconium dioxide particulate reinforced Aluminium 7068 composites
Abstract: The current work emphasis on the tribological characterization of Zirconium dioxide (Zirconia, ZrO2) particulates reinforced Aluminium 7068 metal matrix composites for different process variables established following design of experiments methodology and consequent taguchi based validation techniques for wear prediction. The pin on disc wear test is carried out on specimens fabricated enroute ultrasonic assisted stir casting with controlled dispersion of 12 Wt.% of ZrO2 and subsequent machining of the castings …
Published in International Journal of Metallurgy and Alloys · Vol. 4, Issue 1, 2018 · pp. 37–50 Read article
-
Optimization of Wear Parameters for Medical Implant Applications
Abstract: The purpose of the present research is to check the capability of SS 304 for the application of medical implants and describe the influence of sandblasting process, applied load, frequency, sliding distance on the coefficient of friction of SS 304. In this research, attempts have been made to study the wear behavior of SS 304 at various conditions. In the tribology lab wear test was carried out in accordance with …
Published in International Journal of Composite Materials and Matrices · Vol. 11, Issue 2, 2025 · pp. 1–10 Read article
-
Design And Fabrication Of Foot Wear Garbage Reinforcement Fly Ash And Paver Block
Abstract: Nowadays, the paving blocks and fly ash that in the market are heavy and the price are costly. This study will introduce the lightweight paving blocks and more affordable because the foot wear waste materials are use in the development of the concrete paving blocks and fly ash bricks namely as Eco-Friendly Paving Block and fly ash are make. Eco paving blocks will be compared to control paving blocks due …
Published in International Journal of Manufacturing and Materials Processing · Vol. 9, Issue 2, 2023 · pp. 32–37 Read article
-
Sliding wear behavior of plasma sprayed NiCrAlY-WC based composite coatings on AA5083 alloy
Abstract: WC based coatings was deposited by thermal spray process have been extensively used in industrial application to counter abrasive type of wear. In this study, for the first time NiCrAlY-WC based composite coatings were deposited on AA5083 substrate by plasma sprayed coating technique. The composite coatings were characterized by optical microscopy (OM), scanning electron microscopy (SEM) and microhardness. Sliding wear behavior of coated and uncoated samples was carried out on …
Published in International Journal of Composite Materials and Matrices · Vol. 4, Issue 2, 2018 · pp. 21–26 Read article
-
An Energy-Efficient CMOS Analog Front-End for Wearable Biomedical Monitoring Applications
Abstract: Because wearable biomedical monitoring technologies allow for continuous, real-time, and remote measurement of physiological parameters, they are quickly becoming a key component of contemporary healthcare. These systems place stringent demands on the analog front-end (AFE), which must accurately acquire and condition extremely low-amplitude biopotential signals such as electrocardiogram (ECG), electroencephalogram (EEG), and electromyogram (EMG) while operating under severe power and size constraints. This paper presents the design and simulation of …
Published in International Journal of Microelectronics and Digital integrated circuits · Vol. 12, Issue 1, 2026 · pp. 1–10 Read article
-
A Review on Artificial Intelligence, Internet of Things and Wearable Technology for Smart Healthcare
Abstract: The healthcare industry is no longer an isolated area unaffected by technology advancements. Healthcare is driven by technology more than any other force, and it will continue to evolve in spectacular ways in the future. Artificial Intelligence, Internet of Things, Big Data, Cloud Computing, Smart Wearables, and other cutting-edge healthcare technologies have transformed traditional healthcare into smart healthcare. Technology has allowed us to keep a close eye on our health …
Published in International Journal of Distributed Computing and Technology · Vol. 7, Issue 1, 2021 · pp. 26–34 Read article
-
Characterization and Wear Behavior of TiN, TiAlN, TiCrN and AlCrN PVD Coatings Deposited onto AISI H13 Hot Forging Die Steel
Abstract: Four Nitride coatings TiN, TiAlN, TiCrN and AlCrN were deposited onto AISI H13 hot work die steel by cathodic arc evaporation physical vapour deposition (PVD) technique. The coatings were characterized by SEM, SEM-EDS, XRD, line scan EDS and X-Ray mapping tests and micro hardness tester. The wear characteristics were investigated using a pin on disc method at high temperature and speed against En-31 bearing steel disc. It was observed that …
Published in International Journal of Metallurgy and Alloys · Vol. 4, Issue 2, 2018 · pp. 1–11 Read article
-
Three body Abrasive wear behavior of A356 Aluminum alloy in different Solution treated condition
Abstract: In the present study, solution treatment of A356 Al alloy was carried out in three different ways namely T4-Solution Treatment – TB Condition, T5-Precipitation (Ageing) – TE Condition and T6-Solution Treatment and Precipitation Hardening – TF Conditions. Three body abrasive tests were carried out for all the solution treated samples as well as base metal. The influence of the heat treatment on the microstructure, hardness and abrasive wear resistance behaviour …
Published in International Journal of Composite Materials and Matrices · Vol. 4, Issue 2, 2018 · pp. 27–32 Read article
-
Improving Durability of Asphalt Pavement Wearing Course Submerged in Water Using Candle Wax as Water Proofing Agent: An Assessment Using RSI, FDI and SDI
Abstract: Asphalt pavements are designed and constructed to meet mostly stability and durability requirements during its design life. However, durability of asphalt pavements also heavily depends on other physical parameters as good drainage facility apart from having good material mix and structural designs. In the wake of asphalt pavements not supported by good drainage measures it is very likely that these pavements will fail sooner than later. On this basis, the …
Published in International Journal of Concrete Technology · Vol. 3, Issue 2, 2017 · pp. 1–10 Read article
-
Wearable Textile Antenna for Body Centric Wireless Application
Abstract: This article introduces minimal effort wearable textile antenna with the absconded ground is proposed. The foreseen antenna can get the recurrence between 2.185 and 6.625 GHz. An examination between the measured result and the estimated result has been considered in this article. The foreseen wearable antenna is appropriate to get radio wave vitality accessible in the range of 2.185–6.625 GHz. Keywords: copper tape, flexible antenna and CST software, jeans substrate, …
Published in International Journal of Microwave Engineering and Technology · Vol. 4, Issue 2, 2018 · pp. 27–32 Read article
-
Experimental Investigations for Comparing the Effectiveness of Heat Treatment and Cryogenic Treatment on Wear Performance of EN-47 Spring Steel
Abstract: EN-47 spring steel is chromium, vanadium steel which consists of carbon (0.45–0.55%), manganese (0.50–0.80), silicon (0.50%), phosphorus (0.06%), and sulphur (0.06%) along with chromium (0.80–1.20%) and vanadium (0.15%). Due to this composition EN-47 spring steel become harder and tougher. It has a wide range of applications like crankshafts, steering knuckles, gears, spindles, pumps, suspension etc. So, in this experimental study we treated EN-47 spring steel with cryogenic treatment, cryogenic and …
Published in International Journal of Manufacturing and Materials Processing · Vol. 9, Issue 2, 2023 · pp. 1–9 Read article
-
Parametric Analysis of Reciprocating Friction and Wear Behavior of PTFE Composite.
Abstract: When filler materials like carbon, graphite, glass fibres are added in the PTFE, a composite is formed which improves mechanical & thermal properties of that composite. It increases hardness and wear resistance, while the coefficient of friction is slightly affected and remains low. In this survey, we study various papers in which various methods & experiments were carried out for calculating friction & wear resistance of various compositions of polymers. …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 1, 2018 · pp. 55–61 Read article
-
Optimization of Wear Parameters for Medical ImplantApplications
Abstract: The purpose of the present research is to check the capability of SS 304 for the application of medicalimplants and describe the influence of sandblasting process, applied load, frequency, and slidingdistance on the coefficient of friction of SS 304. In this research, attempts have been made to study thewear behavior of SS 304 under various conditions. In the tribology lab, a wear test was carried out inaccordance with the scheme …
Published in International Journal of Composite Materials and Matrices · Vol. 11, Issue 2, 2025 · pp. 1–10 Read article
-
Thermal Effects on Elastic and Rigidity Modulus of Flexible Pavement Wearing Course
Abstract: Laboratory investigation of flexible pavement was carried out using asphalt concrete samples to simulate the behaviour of actual field conditions of a flexible pavement. The study was carried out in order to ascertain the changes that will result in the elastic and rigidity (shear) modulus of flexible pavement when subjected to increasing temperature conditions (thermal effect). The study became pertinent because mechanistic design of flexible pavement requires as input the …
Published in International Journal of Transportation Engineering and Traffic System · Vol. 3, Issue 2, 2017 · pp. 1–7 Read article
-
Fabrication of Compact Flexible Antennas Using Exotic Nano, Metamaterials for Wearable and Bio Medical Applications
Abstract: Flexible antennas become a growing number of things as part of the rising demand for accessible, wireless IoT-based medical equipment. This paper majorly focuses on the various methods of fabrication of these flexible antennas. Here, several kinds of design innovations, novel materials, and innovative methods of manufacturing are laid out. Hence this review paper justifies the need for flexible antennas, processes used for fabricating them and their significance.
Published in International Journal of Microwave Engineering and Technology · Vol. 8, Issue 2, 2022 · pp. 1–7 Read article
-
International Journal of Manufacturing and Materials Processing
Abstract: Friction and wear resistance were studied on SiC-based novel ceramic composite for applications in advanced automotive braking systems. In the present work, SiC-based ceramic composite was prepared by solid-state reaction synthesis route using a fine powder of precursors. The product was investigated for wear rate under different load conditions in the range from 10N to 70N and speed conditions in the range from 0.13 m/s to 0.52 m/s. The present …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 1, 2021 · pp. 14–24 Read article
-
Maximizing Void Properties from Optimized Local Pozzolans in Wearing Course of Bituminous Concrete Mixtures
Abstract: Failure of asphalt pavement has influenced research into better ways to optimize local pozzolans seenas waste and reduce cost of importation of admixtures. Waste Shell Ashes are checked as localassembled by incorporating them in asphalt concrete mix design. Different research has shown thatsome agricultural waste/by-products can be admitted as mineral fillers in hot-mix asphalt concrete toobtain certain desirable properties. It is on this basis that this research attempts to interrogate …
Published in International Journal of Structural Mechanics and Finite Elements · Vol. 7, Issue 2, 2021 · pp. 47–54 Read article
-
Fabrication of a Cost-Effective Bulletproof Vest Made of Composite Materials
Abstract: Bulletproof vests have evolved significantly, with composite materials like felt, M Sand, and silicone rubber sealant ushering in a new era of personal protection. These unconventional composites offer a unique blend of ballistic resistance, cost-efficiency, and wearer comfort. Felt, a pliable material, adds a layer of protection by effectively absorbing and dissipating kinetic energy from projectile impacts. Its flexibility enhances wearer comfort, setting it apart from traditional materials’ Sand, a …
Published in International Journal of Manufacturing and Materials Processing · Vol. 10, Issue 2, 2024 · pp. 16–31 Read article