Search
101 articles for “Load Distribution”
-
THE STUDY OF DIELECTRIC PERMITTIVITY OF NINPs-PDMS
Abstract: Nickel–polydimethylsiloxane (Ni–PDMS) nanocomposites were fabricated to investigate the influence of metallic nanoparticle loading on the dielectric behavior of flexible polymer matrices. Nickel nanoparticles with controlled size distributions were dispersed in PDMS using solution blending and curing protocols optimized to minimize agglomeration. The dielectric permittivity and loss tangent of the resulting nanocomposites were measured across a broad frequency range (typically 10²–10⁶ Hz) and at varying filler volume fractions. Results show a …
Published in International Journal of Electrical Power System and Technology · Vol. 11, Issue 2, 2025 · pp. 39–50 Read article
-
Analysis of Different Methods used in Reactive Power Compensation: A Review
Abstract: This paper is an overview of the different technologies used in reactive power compensation. Generally, the compensation of reactive power is due to two reasons. The first is to compensate for load and secondly for voltage support. To improve voltage regulation, stability in transmission and distribution system and also to improve power factor Var compensator and Var generators used. Many types of self-commuted generators and various new technologies with lots …
Published in International Journal of Electrical Power System and Technology · Vol. 7, Issue 1, 2021 · pp. 1–12 Read article
-
Fault Current Limiting by Using Series Transformer
Abstract: In this study, we have built the series transformer-based solid-state Fault Current Limiter for distribution station. In the distribution line, overcurrent condition occurs very often which increases the chances of damaging the load. By using this system, we can detect the overcurrent. By using the measuring circuit of PZEM004 Current Sensor, overcurrent condition can be easily detected; and by taking it as a reference, the automatic current limiting process can …
Published in International Journal of Power Electronics Controllers and Converters · Vol. 5, Issue 1, 2019 · pp. 10–18 Read article
-
Design and Simulation of Improved Particle Swarm Optimization Based Capacitor Placement in Distributed Generation System
Abstract: A major investigation was carried out to arrange the optimal condenser arrangement for the powerfactor adaptation, improvement of the voltage profile and the decrease of losses within theappropriation frameworks. In particular, a mechanical plant has large inductive loads withunpredictable load conditions and an incredibly low power factor. In most situations, the key reasonwhy a customer sends a condenser bank is to keep the power bank free from punishment. Power factoris …
Published in International Journal of Power Electronics Controllers and Converters · Vol. 7, Issue 1, 2021 · pp. 1–10 Read article
-
CAE Analysis and Material Selection for Chassis of 4-Wheel Efficycle
Abstract: ABSTRACT This paper presents a comprehensive Computer-Aided Engineering (CAE) analysis and material selection study for the chassis of a four-wheel Efficycle — a hybrid human-electric powered vehicle designed for student competitions and sustainable mobility applications. The objective of the study is to evaluate the structural integrity, stiffness, and crashworthiness of the chassis under various loading scenarios including front impact, side impact, rollover, and torsional loads. Using CAD models developed in …
Published in International Journal of Computer Aided Manufacturing · Vol. 11, Issue 2, 2025 · pp. 9–18 Read article
-
CAE Analysis and Material Selection for Chassis of 4-Wheel Efficycle
Abstract: ABSTRACT This paper presents a comprehensive Computer-Aided Engineering (CAE) analysis and material selection study for the chassis of a four-wheel Efficycle — a hybrid human-electric powered vehicle designed for student competitions and sustainable mobility applications. The objective of the study is to evaluate the structural integrity, stiffness, and crashworthiness of the chassis under various loading scenarios including front impact, side impact, rollover, and torsional loads. Using CAD models developed in …
Published in International Journal of Computer Aided Manufacturing · Vol. 11, Issue 2, 2025 · pp. 1–10 Read article
-
Novel Integrated, Distributed Generation Approach with Renewable Energy Interface with HVDC, A Key Solution To The Future Challenges
Abstract: The recent development in the integrated energy generation as well the distributed generation with the offshore wind farms provides good solution and an experienced significant growth to meet the load demand in recent years. Technical knowledge allow the design of wind farms at higher distances, making the high voltage dc (HVDC) transmission a real alternative to current high voltage ac (HVAC) transmission. When the network is decoupled from the wind …
Published in International Journal of Electrical Power System and Technology · Vol. 1, Issue 2, 2015 · pp. 17–23 Read article
-
Seamless Connectivity and Efficient Resource Allocation in IoT Forensics and Bio-inspired
Abstract: The convergence of cloud computing and the Internet of Things has reshaped many industries, enabling seamless device connectivity and resource allocation on a massive scale. This paper highlights the challenges bio-inspired Internet of Things networks and Internet of Things forensics pose while delving into the core components of achieving connectivity and resource provisioning within cloud-based Internet of Things environments. Different state-of-the-art technologies have been taken into account to enhance reliability …
Published in International Journal of Telecommunications & Emerging Technologies · Vol. 10, Issue 2, 2024 · pp. 8–15 Read article
-
Generative Lightweighting of Actuator-Integrated Robotic Structures Under Decentralized Additive Manufacturing Constraints
Abstract: This study presents the implementation and structural validation of a constraint-driven generative design methodology for the development of lightweight actuator-integrated robotic components fabricated using decentralized additive manufacturing. Building upon a previously formalized constraint-driven framework, the method was applied to the synthesis of a modular robotic link representative of actuator-integrated structural elements commonly used in legged robotic systems. The baseline component was defined to preserve critical functional interfaces, including actuator mounting …
Published in International Journal of Mechanics and Design · Vol. 12, Issue 1, 2026 · pp. 44–60 Read article
-
A Review on Grid Interconnection of Renewable Energy Sources at the Distribution Level with Power Quality Improvement Features
Abstract: Renewable energy sources (RES) are as a rule progressively associated in appropriation frameworks using power electronic converters. This review paper displays a novel control procedure for accomplishing greatest advantages from these matrix interfacing inverters at the point when introduced in 3-phase 4-wire dissemination frameworks. The inverter is controlled to perform as a multi-function device by incorporating active power filter functionality. The inverter can thus be utilized as: 1) power converter …
Published in International Journal of Electrical Power System and Technology · Vol. 2, Issue 1, 2016 · pp. 20–24 Read article
-
Design and Testing of Transformer Protection System in Substation
Abstract: This study proposes a methodology and guidelines for distribution engineers to show that by testing and auditing of DTs, a generalized computer program is used to evaluate any given DTs system. This results in improving the stability as well as energy handling capacity of the system at minimum cost. A distribution network is selected for rehabilitation on the basis of certain planning criteria such as voltage drop, power loss equipment …
Published in International Journal of Electrical Power System and Technology · Vol. 5, Issue 1, 2019 · pp. 17–23 Read article
-
Transient Circuit Breaker Stresses in Networks Including Long Overhead Lines with Multiple Tower Spans
Abstract: Abstract: This paper proposes a new technique for analyzing the recovery voltages in circuit breakers of high voltage networks comprising strongly non-uniform lines. As a representative example, the model considers transmission lines comprising multiple cascade-connected tower spans the resulting information is crucial for assessing the proper operation and protection of those networks. The mathematical model is based on a system composed of simultaneous partial differential and algebraic equations. They formulate …
Published in International Journal of Microelectronics and Digital integrated circuits · Vol. 11, Issue 1, 2025 Read article
-
Soft Computing Techniques for the Integration of Distributed Energy Resources (DERs)
Abstract: One of the most attractive uses of AI in the energy sector is the integration of Distributed energy resources. Distributed energy resources relate to grids, the more complex energy networks are becoming for utilities to operate and manage. Mechanisms such as load and generation forecasting, demand response, power quality management, and voltage regulation, which have traditionally been used to manage DERs and the grid, are not sufficient. This is where …
Published in International Journal of Distributed Computing and Technology · Vol. 8, Issue 2, 2022 · pp. 1–16 Read article
-
A study on C, H and L type prismatic buildings for Synoptic wind flow.
Abstract: The atmospheric boundary layer can be defined as part of the troposphere at the lowest level which is influenced by the presence of the earth’s surface, and responds to surface forcing within a timescale of about an hour or less. The boundary layer depth might differ from hundreds of meters to a few kilometers. The wind that blows due to Atmospheric Boundary Layer is known as synoptic wind. Moreover, thunderstorms …
Published in International Journal of Construction Engineering and Planning · Vol. 6, Issue 1, 2020 · pp. 6–14 Read article
-
Enhancing Agricultural Efficiency Through Auto Farm Monitoring Systems with IoT Integration
Abstract: This paper introduces an affordable and adaptable home control and environmental monitoring framework. It utilizes an embedded micro-web server within an Arduino Mega 2560 microcontroller, enabling IP connectivity to remotely access and manage devices and appliances. Control is facilitated through either a web application or a Bluetooth-enabled Android smartphone app. The system's functionality is demonstrated by integrating devices like light switches into the proposed home control setup. With technological advancements, …
Published in International Journal of Power Electronics Controllers and Converters · Vol. 9, Issue 2, 2023 · pp. 20–28 Read article
-
Assessing the Impact of Soil-Structure Interaction on Seismic Performance of Step Back and Set Back Buildings on Sloping Ground
Abstract: When constructing framed structures on sloping ground, either step back or step back and set back configurations are typically adopted. Due to the varying heights of columns towards the slope and the unsymmetrical nature of these buildings, they are subject to large forces such as shear forces, bending moments, torsional moments, and unequal distribution. In the past, it was common practice to assume that structures were fixed at the base, …
Published in International Journal of Geological and Geotechnical Engineering · Vol. 8, Issue 2, 2022 · pp. 36–47 Read article
-
Enhancing the Performance of Vertical Cryogenic Insulated Cylinders: A Study on Neck Tube Thermal Stress using ANSYS Software
Abstract: An essential supporting component of cryogenic insulated cylinders is the neck tube. The root of the neck tube, which serves as a crucial support structure between the inner and outer vessels in cryogenic insulated cylinders, turns out to be the weakest link due to a hole in the inner upper end for joining. This paper's major goal is to offer research on thermal stress analysis and the optimal construction of …
Published in International Journal of Structural Mechanics and Finite Elements · Vol. 9, Issue 1, 2023 · pp. 37–49 Read article
-
Study of Dynamic Mechanical and Thermal Properties of Poly(Ether Ether Ketone) Carbon Nanotubes
Abstract: The effect of polyetherimide (PEI) as a compatibilizing agent on the morphology, thermal, electrical and dynamic-mechanical properties of poly(ether ether ketone) (PEEK)/single-walled carbon nanotube (SWCNT) nanocomposites, has been investigated for different CNT loadings. After a pre-processing step based on ball milling and premixing under mechanical treatments in ethanol, the samples were prepared by melt extrusion. A more homogeneous distribution of the CNTs throughout the matrix is found for composites containing …
Published in International Journal of Polymer Science and Engineering · Vol. 3, Issue 1, 2017 · pp. 1–21 Read article
-
Microgrid Sources and Power Electronic Interfaces: A ComprehensiveReview on Source Characteristics, Converter Design, Protection, Power Quality, and Energy Storage Integration
Abstract: Microgrids have become a prospective technology in improving energy reliability, sustainability, and resilience through a combination of a variety of distributed energy sources, sophisticated power electronic interface, and energy storage systems. In this paper, there is an in-depth discussion of the source of microgrids, its fundamental features, and how it works and the criteria that may be used in selecting the source of microgrids depending on the factors involved and …
Published in International Journal of Power Electronics Controllers and Converters · Vol. 11, Issue 2, 2025 · pp. 30–61 Read article
-
A Study on Stress Analysis of Aluminum Alloy Solidified in Metallic Molds
Abstract: Abstract The casting technique is regarded as the primary manufacturing process. It has several process parameters that affect the cast structure. Mold geometry is considered one of the most important metal parameters to cast. In the current work, the influence of mold geometries on mechanical properties (deformation and stress concentration) of liquid Aluminum alloy solidified in the steel mold is assessed using ANSYS simulation software. Molds were subject to a …
Published in International Journal of Manufacturing and Materials Processing · Vol. 10, Issue 2, 2024 · pp. 10–15 Read article