All articles
103 articles
-
Computer Aided Assembly Line in an Automobile Industry for Supply Chain Management System Optimization: A Review
Abstract: Computer aided assembly line in an automobile industry for supply Chain Management is an important factor to sustain organization in today competitive world. In this respect, many of the organizations and study have performed to opt out factors that affect either positively or negatively on SCM. In today’s era, Supply Chain Management has changed the world with their production system. By removing activities in the manufacturing process that were not …
Published in International Journal of Computer Aided Manufacturing · Vol. 6, Issue 1, 2020 · pp. 1–18 Read article
-
Software Numerical Simulation on Earth Tube Heat Exchanger Where Air as A Flow Medium
Abstract: Renewable energy is free in nature and it must be brought into application. Due to use of air conditioning and its refrigerants global warming is a serious issue. Renewable energy is the main concept of an earth tube heat exchanger, which uses the thermal energy of the ground for cooling and heating of the fluid medium. Here, air is used as fluent working medium. The air cools in summer and …
Published in International Journal of Computer Aided Manufacturing · Vol. 6, Issue 1, 2020 · pp. 19–45 Read article
-
Design, Simulation and Analysis of Jato Full Cone Nozzle to Compare Theoretical and Analytical Results Using Ansys CFX Software
Abstract: A spray nozzle is a device that facilitates formation of spray in a particular manner due to its shape or design. It atomizes the liquid into spray of droplets. It is often a pipe or a tube of varying cross sectional area and it can be used to direct or modify the flow of liquid. It is used to control rate of flow, speed, spray angle, pressure of the stream …
Published in International Journal of Computer Aided Manufacturing · Vol. 6, Issue 1, 2020 · pp. 57–65 Read article
-
Optimization and Analysis of Pulsation Dampener
Abstract: This paper presents a new method for generating computer-aided models and analysis of pulsation dampeners used in fluid power systems to reduce vibration. Pulsation dampeners are widely used in different energy systems to measure the backlash that is driven by power pumps. The vibrations caused by the power pumps in the water system can be strong enough to cause structural damage to the pipes if the pulsation dampener is not …
Published in International Journal of Computer Aided Manufacturing · Vol. 6, Issue 1, 2020 · pp. 53–56 Read article
-
CFD Analysis and Prediction of Shockwave/Boundary-Layer Interaction at Hypersonic Flows Using RANS Models
Abstract: Interaction of shockwaves with turbulent boundary layer plays an important role in the design and operability of high-speed aerospace vehicles and air-breathing engines. The adverse pressure gradient of the shock is often strong enough to separate the boundary layer. The objective of the present research paper deals with the analysis of hypersonic viscous flows dominated by strong shockwave/boundary-layer interactions (SWBLI) over wing-flap and wing-fuselage junction configurations. The effects of the …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 2, 2019 · pp. 33–50 Read article
-
A REVIEW ON SOFTWARE ANALYSIS OF EARTH HEAT EXCHANGER
Abstract: Renewable energy is the best source of energy. It is abundant in nature, it’s just like a gift of god. Nowadays, heating and cooling is a major issue in environment due to global warming. A major part of energy is being engaged in such issues. So Earth tube heat exchanger is a renewable source of energy for heating and cooling of any building. An Earth Air Tube Heat Exchanger (EATHE) …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 2, 2019 · pp. 26–32 Read article
-
Computational Analysis of Shockwave–Boundary Layer Interaction at Hypersonic Speeds
Abstract: Successful plan of present-day supersonic and hypersonic vehicles requires a comprehension of the physical stream field structure of shockwave–boundary-layer interactions (SWBLIs) and productive reproduction techniques for their portrayal. The significant focal point of this paper is two-dimensional (2D) hypersonic SBLI as well as stream portrayal and physical properties around SWBLIs; be that as it may, even in ostensibly 2D/axis-symmetric streams, the mean stream measurements might be 3D.The objective of the …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 2, 2019 · pp. 1–25 Read article
-
A Review on Performance Analysis of CMOS Inverter
Abstract: In this paper, first we study the various inverter circuits and analyze its performance in terms of noise margin, area, power dissipation and computational delay. After that analyze the various parameter of CMOS Inverter circuit using Pyxis schematic tools of Mentor graphics with TSMC 018 CMOS process technology. Based on this simulation, analyze the rise time, fall time and dynamic power dissipation of CMOS inverter. Finally, we got the good …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 1, 2019 · pp. 29–35 Read article
-
AI Techniques for Data Analytics and Data Science: Software Tools, Research Challenges, Applications: A Review
Abstract: Artificial intelligence is the branch of Computer Science in which multidisciplinary expertise is required and ultimately the main aim is to automate the activities of all human which require human intelligence. The main issue is to design or create machine that completely works like a human brain. Artificial Intelligence architecture focuses on evaluation and redesigns design process. Now days Data Science is most popular all around the world and is …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 1, 2019 · pp. 9–17 Read article
-
Experimental Investigation of Process Parameters on Machining Force, MRR and Power in Turning of AISI 316 Steel
Abstract: A machining process involves many process parameters which directly or indirectly influence the surface quality of the product. A precise knowledge of these optimum parameters facilitate reduce the machining costs and improve product quality. Current investigation aims to investigate the effect of process parameters; cutting speed, feed and depth of cut in turning of SS-316 which is widely used in automobile industries, each varying in three levels. The response characteristics …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 1, 2019 · pp. 18–25 Read article
-
Bidirectional AC-DC Converter for Electric Vehicle Charger
Abstract: This paper presents a single-phase bidirectional ac-dc converter for electrical vehicle charger. The converter is operating in both rectifier and inverter mode depending upon the operation of switches. The bidirectional power flow in rectifier or inverter mode can be achieved by controlling the AC line voltage with PWM technique. For achieving bidirectional flow of power a unipolar or bipolar pulse width modulation (PWM) technique may be applied at ac side …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 1, 2019 · pp. 26–28 Read article
-
Computational Simulation of Continuous Centrifugal Machine using Computational Fluid Dynamics
Abstract: In this paper, the centrifugal machine which is used in a sugar industry has been analysed. The centrifugal machine is used for the separation of the molasses and the sugar crystals from the massecuite. The objective behind the analysis of the flow in the centrifuge is to achieve the reduction in the separation process time using the Computational Fluid Dynamics and to increase the tonnes/hour output of the sugar. The …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 1, 2019 · pp. 1–8 Read article
-
Automobile Engine Assembly Line in an Automobile Industry
Abstract: Manufacturing industries give importance to the reduction of energy consumption due to the increase in energy cost and to create an eco-friendly environment. Assembly line is considered to be one of the cost intensive systems. Robots are recently being used to perform the assembly tasks instead of manual labor. There is a requirement of efficiently balancing the assembly line by allocating equal amount of work to workstations and assignment of …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 2, 2018 · pp. 80–100 Read article
-
Design Improvement of Window Air Conditioner Assembly Using DFMA Technique
Abstract: In this paper, the window air conditioner assembly is analyzed using design for manufacturing and assembly (DFMA) tool. Dewhurst and Boothroyd method is used to perform the analysis. The CAD models are done using CREO PARAMETRIC 2.0. DFMA tool provides the effective cost analysis for the product before manufacturing begins. The outcome of the research shows the increase in design efficiency and decrease in product cost for the redesigned product …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 2, 2018 · pp. 72–79 Read article
-
Workshop Management Processes with Continuous Optimization and Development Techniques
Abstract: Establishment and use of a process that is most efficient are always be the prime concern, but due to some or other reasons, they are not able to do so. Practically, it is not feasible to obtain ideal efficiency because there is something which is lost in every process which is waste or error. Waste reduces the efficiency of the process and also demands require special equipment. The industries need …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 2, 2018 · pp. 38–71 Read article
-
A Study Model of Optimisation Using Kaizen in an Automobile Industry
Abstract: This study provides a sharp and distinct understanding and embodiment of how Faridabad Yamaha Company in the machining industry works with improvements in general and lean in particular. This thesis introduces the development of Kaizen-based maintenance system and their immediate effects on the productivity of industry. In an exploring automobile industry, many techniques are invented and implemented to discover how an automobile manufacturer can bring down his costs, using the …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 2, 2018 · pp. 21–37 Read article
-
Supply Chain Planning and Management in Assembly Line Automobile Industry
Abstract: Yamaha Motors Faridabad has changed the world with their production system. By removing activities in the manufacturing process which were not adding any value to the product, the company could become agile and offer products to the customer with short lead time as well as to a low cost. Companies in other countries needed to change their manufacturing processes in order to stay competitive, and a western variant of the …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 2, 2018 · pp. 1–20 Read article
-
Design and Finite Element Analysis of Refractory Boiler Shell for Optimum Weight
Abstract: This paper deals with the stress analysis of boiler shell with refactory. By using finite element method, a stress analysis has been carried out under the application of pressure at the inner surface of boiler shell. Von-Mises stresses and maximum shear stresses are found. Currently we are working on the condition in order to find temperature distribution so that it will be helpful for us to get thermal analysis and …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 1, 2018 · pp. 48–54 Read article
-
Parametric Analysis of Reciprocating Friction and Wear Behavior of PTFE Composite.
Abstract: When filler materials like carbon, graphite, glass fibres are added in the PTFE, a composite is formed which improves mechanical & thermal properties of that composite. It increases hardness and wear resistance, while the coefficient of friction is slightly affected and remains low. In this survey, we study various papers in which various methods & experiments were carried out for calculating friction & wear resistance of various compositions of polymers. …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 1, 2018 · pp. 55–61 Read article
-
A Modified Memetic Particle Swarm Optimization Algorithm for Sustainable Multi-objective Scheduling of Automatic Guided Vehicles in a Flexible Manufacturing System
Abstract: In the present work, a modified memetic particle swarm optimization (MMPSO) algorithm was applied for a sustainable multi-objective scheduling of automatic guided vehicles AGVs in a flexible manufacturing system (FMS). To achieve sustainable scheduling results for AGVs in FMS, it is imperative to integrate the work center schedule with the AGV schedule, and thereafter, minimize their distance travel and back-tracking in the FMS facility. The work center schedule in the …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 1, 2018 · pp. 33–47 Read article